EVOPEDIA

← all systems · see it in The System

Simple machine

A mechanical device that changes the direction or magnitude of a force: the simplest mechanisms that use mechanical advantage to multiply force, usually the six classical machines (lever, wheel and axle, pulley, inclined plane, wedge, screw); a single applied force does work against a single load force, trading force against distance.

Properties published scienceour proposal

Sourced fields, and our own readings.

born atprehistoric; hand axes (perhaps the first wedge) as early as 1.7 million years ago; levers in use by c. 5000 BC
born precisionvery coarse (contested)
boundaryInside: the rigid link (beam, wheel and axle, sheave and rope, plane, wedge, threaded shaft) and its fixed geometry. On the line: the input point, the output point and the joint at the support (hinge, sliding pair, helix), where forces enter and leave. Outside: the effort's source (a person, animal or another machine), the load, the ground or frame, gravity, and the heat friction makes.
nested levelBuilt from a rigid body joined to its support by one kinematic pair; the elementary building block of compound machines (in series, output of one the input of the next) and the elementary kinematic chain of machine theory. Embedded in human material culture; the idea of it is held by physics and engineering.
scaletechnological

Measures (19) published science

characteristic clock: written theory of simple machines, statics to dynamicsabout 1,850 years, from Archimedes' studies (3rd century BC) to Galileo's complete dynamic theory (1600); derived from the two dated statements
characteristic clock: one stroke of the machine (effort through its distance)set by the user's motion; no source gives a typical stroke time
ideal mechanical advantageMA_ideal = F_out/F_in = v_in/v_out = d_in/d_out, from the machine's geometry (lever: ratio of its lever arms; inclined plane: slope length / height) dimensionless
mechanical efficiency bounds0 < eta < 1 for real machines; 1 only for the ideal (frictionless) machine dimensionless
actual mechanical advantageMA = eta x (v_in/v_out): always less than the velocity ratio in a machine with friction dimensionless
self-locking thresholda machine (and a screw) is self-locking if and only if its efficiency is below 50%
jack screw efficiency15-20% even when well lubricated efficiency
chain or belt drive efficiencyabout 95% (as much as 5% of the power lost to friction heat, deformation and wear) efficiency
compound machine chain yieldeta_compound = eta_1 x eta_2 x ... x eta_N; MA_compound = MA_1 x MA_2 x ... x MA_N dimensionless
block and tackle examplesix rope sections: 100 lbf pulled through 6 ft lifts a 600 lb load 1 ft in the ideal case (IMA 6) lbf, ft
inclined plane example (2% grade, cable)100 lb tension lifts a 4810 lb load
loads moved with levers in ancient Egyptobelisks weighing more than 100 tons
classical simple machines6 (Renaissance list); 5 in the Greek lists (Heron: lever, windlass, pulley, wedge, screw) count
elementary machines collected by Reuleauxover 800 count
weevil screw-and-nut thread extentinner threads of the coxa (nut) covering 345 degrees; external spiral threads of the trochanter 410 degrees
scaling of limb effective mechanical advantage in mammalsEMA rises with body weight as about W^0.25, keeping bone and muscle stresses fairly constant over 0.04-300 kg exponent
bone safety factor kept across mammal sizesbetween 2 and 4 ratio
piranha mass-specific bite force (lever jaws, multipennate muscles)exceeding 1200 N/kg in some species; tooth-specific bite forces from < 1 N to almost 140 N N/kg; N
earliest hand axes (Acheulean, the wedge's first known form)as early as 1.7 million years ago (West Turkana, Kenya)

Open contentions (2) open contention

Where sources or readings disagree. Both stay on the map.

Cross-scale patterns seen here (15) our proposal

Shapes that recur when the same kind of problem is solved at different scales, and how each shows in Simple machine. Each links to every other system that shows it.

Valence: what it trades, and with whom (10) published science

Each exchange with a neighbour, read from both sides: who gains, who pays, and what carries it.

Partners and parts published science

Built from / builds (5)

Sits inside / holds (2)

expressed by (1)

floor filled by (14)

represents (5)

Kinds (10)

wired (1)

Notes published science

Layers

The ways it takes in its world, where they meet, and how it acts back, each from L1 (where it meets the world) up.

the boardroom (shared floors)

  1. L4: Balance of forces and moments in the rigid link: the law of the lever (effort times effort arm equals load times load arm), the statics the Greeks knew; on a ramp, weight, normal force and friction in balance
  2. L5: The work ledger: no source and no store of energy, so work in equals work on the load plus work lost to friction (P_in = P_out + P_fric); less force, more distance, same work
  3. L6: The trade: mechanical advantage = efficiency x velocity ratio; force multiplied at the cost of distance (MA > 1) or distance and speed at the cost of force (MA < 1), or direction changed; self-locking when efficiency is below 50%; in series, advantages and efficiencies multiply

the simple machine as physicists and engineers describe it: effort and load at its contact points up to the trade of force for distance (reader's view)

  1. L1: The world at the machine: one applied force (effort) and one load force, the support it rests on, gravity on the load, the surfaces in contact
  2. L2: Its contact points and joints: input point, output point and the kinematic pair at the support (hinged joint for lever, wheel and axle, pulley; sliding joint for inclined plane and wedge; helical joint for the screw)
  3. L3: The rigid link and its geometry: lever arms, wheel and axle radii, slope over height, wedge angle, thread pitch
  4. L4: Statics: balance of moments about the pivot (the law of the lever), of forces on the plane; friction's hold (angle of repose)
  5. L5: The work ledger: no energy source or store, work in = work out + friction; machines transform energy, they do not create it
  6. L6: The trade delivered to the load: mechanical advantage = efficiency x velocity ratio; force for distance or the reverse, direction changed; self-locking below 50% efficiency; stages in series multiply

way in: Effort (the applied input force)

  1. L1: The effort: a push, pull or twist from a person, an animal or another machine's output, applied at one point
  2. L2: The input point: the end of the effort arm, the wheel's rim (drive force applied tangentially), the free rope end, the wedge's blunt end, the screw's handle
  3. L3: Carried by the rigid link: the lever arm, the wheel radius, the rope over the sheave, the slope; for the screw the input is a torque and an angular velocity

way in: Friction at the contacts (inner)

  1. L1: Surfaces in sliding or rolling contact: threads, plane and load, wedge and wood, axle in bearing, rope in sheave; lubricant or water between them changes the friction
  2. L2: The friction force: the normal force times the coefficient of static friction, opposing motion
  3. L3: The angle of friction (repose): the steepest slope a load rests on unaided; a wedge binds below the arctangent of the friction coefficient

way in: Gravity (weight of load and parts)

  1. L1: Earth's gravity on the load (and on the machine's own parts)
  2. L2: On a ramp the weight splits: the component mg sin(theta) along the plane is what the effort must meet
  3. L3: The slope sets the force: a long, shallow ramp needs less force over more distance, for the same final mgh

way in: Load (the resistance)

  1. L1: The load or resistance: a weight to lift, wood to split, parts to clamp, a ship to haul
  2. L2: The output point: the load arm's end, the axle, the movable pulley block, the wedge's faces, the nut
  3. L3: The load force carried back along the link toward the pivot or plane

way in: Making (the geometry the maker gives it)

  1. L1: The material: flint chipped to a bifacial edge, wood, antler, bronze, iron
  2. L2: Shaping: knapping stone; threads cut laboriously by hand, then on screw-cutting lathes from the 15th century
  3. L3: The fixed geometry: arm ratio, wheel and axle radii, slope, wedge angle, thread pitch and thread angle

way in: Support (fulcrum, bearing, plane, nut)

  1. L1: The fixed ground, frame or surface the machine rests on
  2. L2: The kinematic pair at the support: a hinged joint (fulcrum, bearing, axle, sheave), a sliding joint (the inclined plane's and wedge's faces) or a helical joint (screw in nut)
  3. L3: The reaction at the joint: the bearing serves as a fulcrum, so moments can balance about it

way out: Friction heat

  1. L1: Heat to the surroundings
  2. L2: Sliding surfaces (threads, bearings, rope and sheave) dissipate it
  3. L5: The power lost to friction, P_fric = P_in - P_out

way out: Output force and motion on the load (lift, split, press, turn)

  1. L1: The load moved: obelisks raised, wood and stone split, a vise closed, a ship hauled
  2. L2: The output point presses on the load; the wedge's faces push normal to themselves
  3. L3: Out along the load arm, the axle, the movable block, the wedge's faces, the screw's axis
  4. L6: The changed force: larger and slower, smaller and faster, or turned in direction

way out: Overhauling (running backwards)

  1. L1: The load force does work on the input force: the effort arm moves back against the user
  2. L2: The input point driven backwards
  3. L4: The load's moment exceeds the effort's

way out: Self-locking hold

  1. L1: The load held where it was left: bolts and wood screws stay tight, the jack stays up, the wedge stays in the wood
  2. L2: Friction at the threads, the plane or the wedge's faces
  3. L6: Efficiency below 50%: the work friction takes exceeds what the load could do running it backwards

way out: Wear and deformation

  1. L1: Material lost from the contact surfaces; the machine itself slowly changes
  2. L2: Chains and belts stretch and wear; thread angle sets the wear rate of screws
  3. L5: Losses to wear and deformation (the ideal machine has rigid bodies that do not deflect or wear)

way out: What the hand feels back (resistance and impacts through the tool)

  1. L1: At the hand: the person locates the contact on the rod as accurately as on the skin
  2. L2: The tool's vibration modes, which encode where it was struck (a pre-neuronal stage of processing)
  3. L4: The load's resistance and any impact carried back through the rigid link

Sources (25) published science

Simple machine (Wikipedia, via Wikimedia Enterprise snapshot 2026-11-01)
Miller LE, Montroni L, Koun E, Salemme R, Hayward V, Farne A (2018) Sensing with tools extends somatosensory processing beyond the body. Nature 561:239. doi:10.1038/s41586-018-0460-0 (behind its links)
Lever (Wikipedia, via Wikimedia Enterprise) (behind its links)
Wedge (mechanical device) (Wikipedia, via Wikimedia Enterprise) (behind its links)
Gear (Wikipedia, via Wikimedia Enterprise snapshot 2026-11-01) (behind its links)
Tool (Wikipedia, via Wikimedia Enterprise snapshot 2026-11-01) (behind its links)
Mechanical efficiency (Wikipedia, via Wikimedia Enterprise snapshot) (behind its links)
Screw (simple machine) (Wikipedia, via Wikimedia Enterprise) (behind its links)
Mechanical advantage (Wikipedia, via Wikimedia Enterprise) (behind its links)
Inclined plane (Wikipedia, via Wikimedia Enterprise) (behind its links)
van de Kamp T, Vagovic P, Baumbach T, Riedel A (2011) A biological screw in a beetle's leg. Science 333:52. doi:10.1126/science.1204245 (behind its links)
Biewener AA (2005) Biomechanical consequences of scaling. Journal of Experimental Biology 208:1665. doi:10.1242/jeb.01520 (behind its links)
Biewener AA (1989) Scaling body support in mammals: limb posture and muscle mechanics. Science 245:45. doi:10.1126/science.2740914 (behind its links)
Huskey S, Fletcher K, Kolmann M, et al., Westneat MW (2026) Biomechanics, muscle modeling, and the elevated bite force and tooth stress of piranhas. Naturwissenschaften. doi:10.1007/s00114-026-02071-w (PMC12886308) (behind its links)
Stone tool (Wikipedia) (behind its links)
Norbury JW (2006) Working with simple machines. Physics Education 41:546-550; arXiv:physics/0612109 (behind its links)
Wheel and axle (Wikipedia, via Wikimedia Enterprise) (behind its links)
Tool use by animals (Wikipedia, via Wikimedia Enterprise snapshot 2026-11-01) (behind its links)
Fall A, Weber B, Pakpour M, et al., Bonn D (2014) Sliding friction on wet and dry sand. Physical Review Letters 112:175502. doi:10.1103/PhysRevLett.112.175502 (behind its links)
Pulley (Wikipedia, via Wikimedia Enterprise) (behind its links)
Uyeda TQ, Abramson PD, Spudich JA (1996) The neck region of the myosin motor domain acts as a lever arm to generate movement. PNAS 93:4459. doi:10.1073/pnas.93.9.4459 (PMC39560) (behind its links)
Azizi E, Brainerd EL, Roberts TJ (2008) Variable gearing in pennate muscles. PNAS 105:1745. doi:10.1073/pnas.0709212105 (PMC2234215) (behind its links)
Burrows M, Sutton G (2013) Interacting gears synchronize propulsive leg movements in a jumping insect. Science 341:1254. doi:10.1126/science.1240284 (behind its links)
Alfaro ME, Bolnick DI, Wainwright PC (2005) Evolutionary consequences of many-to-one mapping of jaw morphology to mechanics in labrid fishes. American Naturalist 165:E140. doi:10.1086/429564 (behind its links)
Osiurak F, Federico G, Fournel A, et al. (2025) Shaping the physical world to our ends through the left PF technical-cognition area. eLife. doi:10.7554/eLife.94578 (PMC12005713, CC BY) (behind its links)