← all systems · see it in The System
Gear
A gear (gearwheel, toothed wheel, cog) is a rotating machine part that transmits rotational motion or torque by a series of teeth that engage compatible teeth of another gear or part; meshing gears (a gear train) trade torque for rotational speed between axles, change the axis of rotation or invert its sense, and with a rack turn rotation into linear motion. As mechanical engineering describes it: tooth profiles (involute, cycloidal) shaped for a constant angular-velocity ratio, gear ratios set by tooth counts, trains, wear and failure; also found evolved in insects (planthopper nymphs' leg gears, horned beetles' mandibular gear-like structures).
Properties published scienceour proposal
Sourced fields, and our own readings.
| born at | 4th century BC (earliest surviving gears, China); Aristotle mentions gears around 330 BC |
| born precision | century |
| boundary | Inside: the gear body (rim, web, hub and bore) and its teeth, with their tooth faces (the action surface: the only part of the surface that presses on the mate in normal operation). On the line: the tooth flanks in contact with the mating gear or rack along the line of action, and the bore where the shaft carries it. Outside: the mating gear, the shaft and its bearings, the frame that fixes the centre distance, the lubricant, the driving power source and the load, the maker, the air the noise goes into and the heat sink. |
| nested level | Built from a rigid body (the wheel) with N teeth in N-fold rotational symmetry; one member of a gear pair; pairs in series make gear trains, which sit inside machines as mechanisms. The gear is the machine element; the idea of it (tooth geometry, the fundamental law of gearing) is held by mechanical engineering. |
| scale | technological |
Measures (27) published science
| characteristic clock: tooth-mesh period | one tooth passes the mesh every 1/N of a turn (N-fold symmetry); the period is 1/(N x rotational frequency); no typical value is given in the sources read |
| characteristic clock: escapement beat | one tooth released per swing of the pendulum or balance wheel |
| Issus hindleg synchronisation | within 30 microseconds |
| gear ratio (torque) | T2/T1 = r = N2/N1; speed ratio is 1/r |
| characteristic clock: history of the kind | about 2,400 years from the earliest surviving gears (4th century BC) to today; derived |
| worm-and-gear ratio range | 10:1 to 500:1 (helical gears normally under 10:1) ratio |
| gear diameter range | a few micrometres (micromachines) to over 10 metres (mining equipment) |
| hypoid single-set ratio | 60:1 and higher ratio |
| high-speed threshold (pitch line velocity) | 25 m/s |
| straight bevel gear speed limit | below 5 m/s, or 1000 rpm for small gears |
| standard pressure angle | 20 degrees most common; 14.5 and 25 much less common |
| share of gearing produced by net shape moulding (2014) | about 80 % |
| maple gear teeth supplied per year (1967) | tens of thousands (one company, Lancaster, New Hampshire) teeth/year |
| Issus nymph gear strip length | 400 micrometres; pitch radius 200 micrometres; 10 to 12 teeth |
| Issus gear tooth height | 15-30 micrometres |
| horned beetle gear-like structure: species with it | 22 of 22 Dynastinae species; 0 of 16 other beetle species |
| horned beetle mandible dislocation load (engaged, left) | 600 (right side about 400) |
| Antikythera mechanism: gears in the 2021 reconstruction | 69 (34 reconstructed in front, 35 behind) gears |
| Antikythera mechanism: surviving gears | 30 (27 in Fragment A); 82 fragments gears |
| Antikythera mechanism: largest gear | about 13 cm across, originally 223 teeth |
| Antikythera mechanism: chain failure probability (1% per pair, 15 pairs) | approximately 14% (5% per pair gives nearly 54%) |
| electric drivetrain mechanical efficiency (including gearbox) | 59-77 % |
| microgear scaling: moment of inertia | scales with the fifth power of size (area with the square, mass with the cube); allowable tooth force with about the square power of scale factor |
| Antikythera mechanism: workable tooth clearance | jams below 10% of tooth height, disengages above 90%; about 40% acceptable |
| nanogear optimal tooth count (graphene disk, 10 nm) | 20 tert-butylphenyl teeth; centre separation 6.5 nm |
| cycling test cadence range | 50 to 110 rpm in 15 rpm steps at a fixed gear ratio; 90 rpm in the gear-ratio trial |
| backlash of a train | the sum of the backlash of each pair length |
Open contentions (5) open contention
Where sources or readings disagree. Both stay on the map.
- C-736 When a system first throws away its excess energy and later learns to store it for reuse, is that one process that grew or two separate ones?
booked: The map keeps both readings side by side and rules neither. A few examples fit the 'one process that grew' reading, but it hasn't been tested.
the other reading: see research/CONTENTIONS.md C-736 - C-2705 What was the first simple machine?
booked: The map keeps the competing readings; none is ruled.
the other reading: see research/CONTENTIONS.md C-2705 - C-3003 Did the Antikythera mechanism actually work?
booked: The map keeps the competing readings; none is ruled.
the other reading: it worked as reconstructed (Freeth 2021); it could not have worked with the measured errors (Szigety & Arenas 2025, who doubt the error values more than the device) - C-3017 Were the first gears made by people or evolved in insects?
booked: The map keeps the competing readings; none is ruled.
the other reading: rung 7: evolved cuticular gears in planthopper nymphs (recognised as early as 1957; functional, Burrows & Sutton 2013) and horned beetle mandibles are older than any made gear; rung 11: hand-made gears read with the simple machines of human culture (as C-2705 books the simple machine) - C-3044 How did the ancient Chinese south-pointing chariot keep its direction?
booked: The map keeps the competing readings; none is ruled.
the other reading: differential gear (Lanchester; the Gear article); geared but not a differential (Needham, as the Differential article reports)
Partners and parts published science
Built from / builds (6)
- Rigid body
- Steel
- Teeth (cogs)
- Drive and load competing for the gear's turning
- Gears against belts, chains, friction drives and fluid couplings for torque transmission
- Wood, metals and plastics competing to be the gear
Sits inside / holds (4)
Trades with (valence) (11)
- Steel via sys:mechanical-contact · Gear gain
- Bearing (mechanical) via sys:mechanical-contact · Gear gain
- Thermal energy (heat, temperature and heat flow) via sys:thermal-energy · Gear loss
- Acoustic wave (sound: pressure waves in matter) via sys:acoustic-wave · Gear loss
- Human (Homo sapiens) via sys:mechanical-contact · Gear mixed
- Insect (class Insecta) via sys:mechanical-contact · Gear gain
- Mechanical engineering (the field) via sys:mechanical-contact · Gear gain
- Escapement (clock movement) via sys:mechanical-contact · Gear mixed
- Gears and gear trains via sys:mechanical-contact · Gear gain
- Machine via sys:mechanical-contact · Gear mixed
- Lubricant (gear oil) via sys:lubricant · Gear gain
expressed by (3)
- Interoperability/Transduction (Bridging)
- Internal Coordination/Regulation
- Quality Control & Error Correction
floor filled by (12)
- Steel
- Thermal energy (heat, temperature and heat flow)
- Human (Homo sapiens)
- Insect (class Insecta)
- Antikythera mechanism
- Mechanical engineering (the field)
- Escapement (clock movement)
- Gears and gear trains
- Machine
- Bearing (mechanical)
- Teeth (cogs)
- Lubricant (gear oil)
represents (2)
- Simple machine
- the gear as a model: Maxwell's idle wheels for electric current; quantum gears for ring molecules; chemical gears for reaction pathways
Kinds (28)
- Simple machine
- Double helical (herringbone) gear
- Bevel gear
- Hypoid gear
- Worm and worm wheel
- Crown (contrate) gear
- Internal (ring) gear
- Rack and pinion
- Epicyclic (planetary) gearing
- Cage (lantern) gear
- Non-circular gear
- Harmonic (strain wave) gear
- Magnetic gear
- Molecular and nanoscale gears
- Planthopper nymph leg gears
- Horned beetle mandibular gear-like structures
- Involute tooth profile
- Cycloidal tooth profile
- Artisanal (triangular-tooth) gears
- Sprocket
- Timing pulley
- Geneva drive
- Idler gear
- Sacrificial (plastic) gear
- Microgear
- Chemical gears (as an analogy)
- Helical gear
- Spur gear
wired (4)
Notes published science
- Gears were invented by insects long before people: young planthoppers have a strip of 10 to 12 gear teeth on each hind leg that lock the two legs together so they kick within 30 microseconds of each other, and then throw the gears away at their last moult (src:burrows-2013-insect-gears, src:wp:gear).
- The Antikythera mechanism's maker could not use the best known Venus cycle because it needed a wheel with 1151 teeth, and 1151 is a prime number: the arithmetic of gearing decided which astronomy the machine could carry (src:freeth-2021-antikythera).
- Gear trains multiply their risks: if each of the Antikythera mechanism's 15 gear pairs jams only 1% of the time, the whole machine fails about 14% of the time, and one jam anywhere stops every pointer (src:szigety-arenas-2025-triangular-teeth).
Layers
The ways it takes in its world, where they meet, and how it acts back, each from L1 (where it meets the world) up.
a gear as mechanical engineers describe it: torque in at the teeth, the mesh, a fixed ratio out along its train (reader's view)
- L1: The world at the gear: the driving torque from a shaft, motor, hand or another gear; the load's resisting torque; the shaft, bearings and frame that fix the axes; the lubricant; the heat and dirt around it
- L2: The teeth: the action surface, N tooth faces (two sets if torque runs both ways), pressed by the mating teeth; all other surfaces irrelevant
- L3: Tooth geometry and body: profile (involute, cycloid, triangular), pitch or module, pressure angle, helix angle, face width; material and heat treatment (hard case, tough core); the fixed centre distance
- L4: The mesh: conjugate action along the line of action; the fundamental law of gearing (constant angular-velocity ratio); zero sliding at the pitch point, sliding elsewhere; at least one contact pair at every moment; backlash to close before reversing
- L5: The ratio and power ledger: torque times r, speed divided by r, direction reversed for external pairs; power in = power out + losses (friction in the meshing phase, fluid losses) turned to heat; fatigue and wear accumulate (pitting, scuffing, root fracture)
- L6: The gear in its train: ratios multiply, backlash adds, an idler reverses, a differential averages, epicyclic trains combine motions; trains count (calculator carries), keep time under an escapement, mechanize astronomical cycles (Antikythera), and lock two legs in step (Issus)
the boardroom (shared floors)
- L4: The mesh: conjugate action along the line of action; the fundamental law of gearing (constant angular-velocity ratio); always at least one contact pair; backlash closed before force reverses
- L5: The ratio and power ledger: torque times r, speed over r; losses in the meshing phase turned to heat; fatigue accumulates
- L6: The gear in its train: ratios multiply, backlash adds, idlers reverse, differentials average; counting, timekeeping, astronomical computing, two legs locked in step
way in: Contact history (the gear's own stress cycles)
- L1: Each tooth's flank and root under repeated loading as it passes through mesh
- L2: Elastic contact stresses near the surface nucleate cracks
- L3: Cracks grow and pieces break away: pits, micropits; at the root, fatigue cracks
- L4: Damaged flanks change the mesh: the effective ratio fluctuates, vibration rises
way in: Drive (input torque and motion)
- L1: The driving torque: from a motor or engine on the shaft, a hand on a crank, a weight or spring in a clock, the other leg's muscles in Issus, or the previous gear
- L2: The driving tooth face presses on the driven face at contact points on the action surface
- L3: The force runs along the line of action, the common tangent to the two base circles (for involute teeth), whatever the mounting distance
way in: Load (the resisting torque)
- L1: The load on the output: vehicle wheels, millstones, a clock's hands, the Antikythera pointers, a rack's slide
- L2: The driven gear's teeth take the reaction; teeth bend at the root (root fatigue fracture)
- L3: The reaction runs back along the same line of action; heavy loads set Hertzian contact pressure on the flanks
way in: Lubrication
- L1: Gear oil or grease (or none: plastic gears need no lubrication); hypoid gears need the most viscous oils
- L2: The film in the contact between flanks
- L3: The friction coefficient lowered; tangential force and surface temperature reduced
- L4: Sliding friction at the mesh (zero at the pitch point, larger in helical and worm meshes) and churning and windage losses depend on oil viscosity
way in: Making (the geometry and material the maker gives it)
- L1: The blank and the maker: casting, injection moulding, powder metallurgy, blanking, hobbing; hand cutting in antiquity
- L2: The tooth form cut or moulded; teeth heat treated
- L3: Geometry with its errors (tooth spacing, eccentricity) and surface hardness
way in: Mounting (shaft, bearings, frame, centre distance)
- L1: The frame, shafts and bearings that hold each axis fixed in space
- L2: The bore on its shaft; thrust bearings for helical gears
- L3: Centre distance and axis alignment: fixed once made; involute teeth tolerate a range, cycloidal need it exact; in hand-made trains too little clearance jams and too much disengages
way in: Surroundings (temperature, dirt, water)
- L1: Temperature, dust and dirt, water and salt (the Antikythera gears spent two thousand years in the sea)
- L2: Exposed flanks and spaces between teeth; in cage gears dirt falls through the rods
- L3: Thermal expansion changes clearances (zero backlash would need uniform expansion); trapped dirt increases wear; corrosion eats bronze
way out: Axial thrust (helical gears)
- L1: Thrust taken by thrust bearings and the frame
- L3: The helix angle sets the thrust; mirrored halves cancel it
- L4: Angled teeth push along the axis as well as round it
way out: Heat (the losses)
- L1: Heat carried off by the lubrication system and housing (worm-drive trucks need a large oil volume to dissipate it)
- L2: Heat at the sliding flanks
- L5: Friction and fluid losses
way out: Noise and vibration
- L1: Sound in the air: spur gears' characteristic whine at high speed; the clock's tick as the escape tooth stops
- L2: Impact and stress at the teeth
- L4: A ratio that fluctuates over each tooth cycle (artisanal teeth) or teeth that meet suddenly across their width (spur gears)
way out: Output torque and motion (to the driven shaft, rack, hands, pointers, the other leg)
- L1: The load moved: wheels driven, a tie rod slid by a rack, a clock's hands advanced, the Moon's phase shown, both hindlegs swung together
- L2: The driven teeth push the output shaft round
- L4: Conjugate motion carried to the driven gear at a constant ratio
- L6: The ratio applied: speed and torque changed, direction set
way out: Self-locking hold (worm sets)
- L1: A position held: the machine head of a stringed instrument stays in tune
- L2: The wheel's teeth lock against the worm's
- L5: The circumferential force from the wheel is not enough to overcome friction
way out: Wear, pits, fracture and the gear's end
- L1: Material lost from the flanks; broken teeth; a failed gearbox
- L3: Pits, micropits, scuffing streaks, cracks
- L5: Fatigue and wear accumulated