← all systems · see it in The System
Bearing (mechanical)
A machine element that constrains relative motion to only the desired motion and reduces friction between moving parts; it lets one part bear (support) another, carrying radial, axial and moment loads from the source of the load to the supporting structure, by sliding surfaces (plain bearings), rolling elements (ball and roller bearings), a fluid film, a magnetic field or a flexing element.
Properties published scienceour proposal
Sourced fields, and our own readings.
| born at | wheeled vehicles on plain bearings, about 5000-3000 BC; rolling bearings by 40 BC (Nemi) |
| born precision | millennia (contested) |
| boundary | Inside: the bearing surfaces or races, whatever sits between them (rolling elements and cage, a lubricant film, a magnetic field, a flexing element), the seals or glands that close it, and the lubricant packed in it. On the line: the fits to the shaft and to the housing bore, where load and motion come in and go out, and the gaps where lubricant, dirt and current cross. Outside: the shaft and the housing (the machine), the load's source, the lubricant supply, the surroundings' heat, dirt and water, stray electric currents, and the people who mount, grease and replace it. |
| nested level | Built from races (or a bearing surface), rolling elements, a cage, seals and lubricant, mostly of bearing steel; a machine element at the machine's floor of elements and joints (it realises the joint a mechanism needs: radial rotation, linear motion, spherical rotation, hinge motion). Embedded in machines from wheelbarrows and bicycles to wind-turbine gearboxes, dental drills and the Mars rover; its making is an industry, its study tribology. |
| scale | technological |
Measures (25) published science
| basic rating life L10 (characteristic clock of one bearing) | L10 = (C/P)^p: the life that 90% of a large group of apparently identical bearings reach or exceed; quoted in millions of revolutions |
| cage (fundamental train) frequency FTF | FTF = (S/2)(1 - (Bd/Pd) cos A): the cage's orbit, a fraction of shaft speed S set by ball and pitch diameters and contact angle Hz (from shaft speed) |
| load-life exponent p | 3 for ball bearings, 4 for pure line contact, 3.33 for roller bearings (life falls with the cube of load over rating for balls) dimensionless |
| median life against L10 | about 5 times L10 ratio |
| Weibull slope of bearing life data | most rolling bearing life data show Weibull slopes between 1 and 2 dimensionless |
| system L10 of a five-bearing planetary set against one bearing | system L10 774 h for a five-bearing planetary set against 3529 h for one double-row spherical bearing hours |
| rolling-element bearing coefficient of friction (steel) | about 0.005 (seals, packed grease, preload and misalignment can raise it to as much as 0.125) dimensionless |
| PTFE plain bearing coefficient of friction | about 0.05-0.35, depending on fillers dimensionless |
| healthy cartilage coefficient of friction (comparison) | healthy porcine 0.001-0.14; healthy human 0.22 (in the test setups reviewed) dimensionless |
| share of world energy consumption from tribological contacts | about 23% (119 EJ): 20% (103 EJ) to overcome friction, 3% (16 EJ) to remanufacture worn parts share of world energy consumption |
| cost of friction, wear and corrosion to the UK economy (Jost 1966) | 1.1-1.4% of GDP share of UK GDP |
| possible cut in friction and wear energy losses | 40% in the long term (15 years), 18% in the short term (8 years) share of friction and wear losses |
| bearing life improvement from steel processing | up to 80 times the late-1950s life, or 400 times the 1940 life ratio |
| real lives against 1924-model predictions (1990s) | up to 14 times longer than predicted ratio |
| fatigue limit stress in ISO 281:2007 | 900 MPa fatigue limit stress (Hertz contact stress 1500 MPa); the ASME method uses 684 MPa (Hertz 1140 MPa) |
| wind-turbine gearbox bearing failures against design life | failures within 5%-20% of design life, by flaking share of design life |
| white structure flaking against L10 life | 1-20% of L10; turbine lifetime from a predicted 20 years to under 2 years share of L10 |
| bearing life with low-density electrical discharges | life cut to 5-10% of the expected L10 at current densities below 1 mA/mm2, often with critical lubricants share of L10 |
| bacterial flagellar motor top speed (bushing-supported rod) | 1700 revolutions per second, with almost 100% efficiency rps |
| play example | 2 mm (a 10 mm shaft in a 12 mm hole); a lathe's ball lead screw held to ±0.002 mm |
| Schweinfurt production loss after the 17 August 1943 raid | 34 percent immediate loss (Speer); 38% (Miller); made up by surpluses share of production |
| Stribeck-curve minima in Hersey number (Martens' data) | about 0.00005-0.00015 Hersey number |
| composite bearing maintenance-free life | up to 30 years |
| characteristic clock: kind-level, plain bearing to modern life standard | from wheeled vehicles on plain bearings (about 5000-3000 BC) to ISO 281:2007; Lundberg-Palmgren's model 1947/1952 years |
| 100Cr6 / SAE 52100 bearing steel composition | Fe 96.5-97.32%, Cr 1.35-1.60%, C 0.93-1.05%, Mn 0.25-0.45%, Si 0.15-0.35% mass % |
Open contentions (8) open contention
Where sources or readings disagree. Both stay on the map.
- C-3004 Do rolling bearings have a load below which they never wear out?
booked: The map keeps the competing readings; none is ruled.
the other reading: Zaretsky: no open data justify a fatigue limit for through-hardened bearing steels such as AISI 52100 and M-50; with it, predicted life approaches infinity and bearings get undersized; Ioannides-Harris / SKF: a fatigue limit explains lives up to 14 times longer than predicted - C-3005 When was the first bearing: made by people, or rollers under sledges?
booked: The map keeps the competing readings; none is ruled.
the other reading: rollers under sledges as the first rolling bearings, earlier than the wheel (speculated, no archaeological evidence); the job is older than people: biological bushings (the flagellar LP ring) and lubricated joints do it, so the kind could be read as born with life and borrowed by makers - C-3006 How is the cartilage in our joints lubricated?
booked: The map keeps the competing readings; none is ruled.
the other reading: one mode dominates; modes act together through the gait cycle - C-3031 Did ancient Egyptians and Assyrians move loads on rollers?
booked: The map keeps the competing readings; none is ruled.
the other reading: Layard's reading: rollers in Assyria some 2700 years ago; no archaeological evidence for rollers before the wheel - C-3032 Where does rolling-contact fatigue in bearings start?
booked: The map keeps the competing readings; none is ruled.
the other reading: surface initiation propagating down to flaking; subsurface initiation at inclusions, microstructural alterations or voids (Richardson 2018 saw subsurface WEC initiation at inclusions) - C-3034 How much did the 1943 Schweinfurt bearing raid cut German production?
booked: The map keeps the competing readings; none is ruled.
the other reading: 38% (Miller); the raid a failure (Eaker and Anderson that evening); vulnerable to a sustained campaign though not to one raid (Speer) - C-3057 Who first described the Stribeck curve of friction?
booked: The map keeps the competing readings; none is ruled.
the other reading: Martens about 1885 at the same institute; Thurston in the mid-1870s - C-3065 What causes white etching cracks in bearings?
booked: The map keeps the competing readings; none is ruled.
the other reading: transient loads (gusts, reversals, braking); electrical discharges at low current density; hydrogen from lubricant, additives or water; tensile hoop stresses
Cross-scale patterns seen here (20) our proposal
Shapes that recur when the same kind of problem is solved at different scales, and how each shows in Bearing (mechanical). Each links to every other system that shows it.
- borrowed-then-held (structural)
Lubrication first supplied from outside (water mills where 'the water provides cooling and lubrication'; workers called oilers with oil cans from the late 1700s to the mid-1900s), later held inside: sealed-for-life bearings carry their own grease behind seals (rare before the 1970s), composite beari - lightning (structural)
Electrical discharges between raceway and rolling elements, a stored voltage released across the oil film, leave fluting and corrugation, or at low current density start white etching cracks that end the bearing at 5-10% of its L10: a discharge after which the bearing is not the same. - runaway from an unstable balance (structural)
An attracting magnet's force 'decreases with increasing distance and increases at decreasing distances': once the rotor is off centre it runs toward the magnet, so active magnetic bearings need a controller to hold the balance (Earnshaw's theorem limits passive ones). Fluid bearings have their half- - same role, different builds (structural)
One job, letting one part move on another with little friction, is met by sliding surfaces, rolling balls, a fluid film, a magnetic field and a flexing element ('by virtue of its shape, by its material, or by introducing and containing a fluid ... or by separating the surfaces with an electromagneti - templating (structural)
One standard module reused unchanged across machines: ISO dimensions and numbering, ISO 281 ratings; Fischer's equal, round balls (1883) set up an independent industry; a bi-material plain bearing made interchangeable with linear ball bearings; the same bearing types from dental drills to the Mars r - The Payment to Entropy (structural)
Every turn pays a toll in heat: rolling friction about 0.005 for steel, viscous dissipation in the EHL film dominating rolling resistance, the oil as heat sink; at world scale about 20% (103 EJ) of energy use goes to overcome friction and 3% (16 EJ) to remanufacture worn parts. Hydrostatic pumps and - trade one property for another (structural)
The kinds of bearing spread along trades: rollers buy radial capacity with axial capacity and friction; needle rollers buy a small outside diameter with fast fatigue; better seals buy lower leakage and pump power with friction; lower fluid viscosity buys low friction with faster leaks and more pump - Umwelt: each system carves its own slice of one shared medium (structural)
Each bearing kind carves its own slice of the same machine world: rolling bearings take load through contact, fluid bearings through film pressure, magnetic bearings through the field; only the active magnetic kind reads its own state (rotor position) by sensors. Its channels (load, motion, lubrican - who opens the door (structural)
The ports are made ahead of time by the maker: ground raceway grooves, grease fittings and oil cups, seal lips that refuse dirt, gap sensors in magnetic bearings. Stray current and heat come in with no door: open field. - barrier-gates-complexity (partial)
Seals keep the dirt out and the grease in, which lets a bearing run sealed for life with no upkeep; without the barrier (a rock crusher's conveyor), the bearing 'is contaminated again as soon as the conveyor resumes', and only frequent relubrication helps. What the seal gates is a held store and lon - coordination-before-mapping (partial)
The balls move together, evenly spaced and in one orbit, with no map or controller: geometry and the cage alone. - holding / entrainment (partial)
The cage sets its rolling elements' spacing and their common orbit (the fundamental train frequency fixed by geometry): the whole holds the count and clock of its parts. - outside-to-inside (partial)
The lubricant reservoir moves from outside the bearing (an oil can, a ring oiler's pool, a sump) to inside it (packed, sealed grease; a self-lubricating liner). The outside phase comes first in the sources (oilers before sealed bearings). - same toolkit, independent builds (partial)
Wood and bronze rolling bearings appear about 2000 years ago in separate places: the Nemi ships (ball, cylindrical and taper-roller forms), a Celtic cart hub from Jutland (bronze collars with wooden rollers), and rival Chinese claims; early American cultures built neither. - The carry (partial)
Overflow passed on: a bearing's gap holds only so much oil; in a ring oiler 'excess oil is flung off and collects in the pool again', and an engine's excess pumped oil 'escapes through a relief valve back into the sump'; a fresh charge of grease pushes the older grit-filled charge out. The wait face - the whole sets the local reference (partial)
A single bearing's life cannot be calculated; it is read against its population (L10: the life 90% of a large group of apparently identical bearings reach), and a set of bearings has a life shorter than its shortest member. - causal ceiling (surface)
Seemingly identical bearings under identical conditions have different lives, so no bearing's own life can be calculated, only a population's; the sources do not say whether this limit is structural or practical. - conservation law plus closure (surface)
Hertz contact theory alone does not give a life: Palmgren noted that Hertz theory does not treat lubrication or mounting stresses, and life prediction needed a statistical law (Weibull 1939, Lundberg-Palmgren 1947) to close it. - partner-becomes-part (surface)
The lubricant, a partner supplied from outside, becomes the bearing's own material in composite bearings ('PTFE acts as a lubricant'). No inheritance (a made part), so surface; the reverse also shows: integral bearings, once part of the machine, became separate bushings with interchangeable manufact - smooth to sharp in finite time (surface)
In the ideal, 'a load on an infinitely small point would cause infinitely high contact pressure'; real balls and races flatten so the singular value is never reached. A geometric idealisation, not a process reaching a singularity.
Valence: what it trades, and with whom (11) published science
Each exchange with a neighbour, read from both sides: who gains, who pays, and what carries it.
- Steel via sys:force · Bearing (mechanical) gain
- Electromagnetic field via sys:electromagnetic-field · Bearing (mechanical) mixed
- Thermal energy (heat, temperature and heat flow) via sys:thermal-energy · Bearing (mechanical) loss
- Human (Homo sapiens) via sys:sensory-environment · Bearing (mechanical) gain
- Industrial Revolution (the first, c. 1760 to c. 1840) via sys:mechanical-work · Bearing (mechanical) gain
- Electric motors via sys:electromagnetic-field · Bearing (mechanical) loss
- Wind turbine via sys:mechanical-contact · Bearing (mechanical) loss
- Machine via sys:mechanical-contact · Bearing (mechanical) mixed
- Gear via sys:mechanical-contact · Bearing (mechanical) mixed
- Lubricant (gear oil) via sys:lubricant · Bearing (mechanical) gain
- Dirt and wear debris (dust, grit, water, metal particles) via sys:wear-debris · Bearing (mechanical) loss
Partners and parts published science
Built from / builds (7)
- Steel
- Lubricant (gear oil)
- Race (bearing ring) or bearing surface
- Rolling elements (balls, rollers, needles)
- Cage (separator)
- Seals and glands
- Surface- and subsurface-initiated cracks competing to end a bearing's life
Sits inside / holds (3)
expressed by (6)
- Interoperability/Transduction (Bridging)
- Internal Coordination/Regulation
- Sensing/Scanning
- Reactive Response
- Physical/Virtual Barrier
- Quality Control & Error Correction
floor filled by (17)
- Steel
- Electromagnetic field
- Thermal energy (heat, temperature and heat flow)
- Electric motors
- Friction
- Kinematic pair (joint)
- Machine
- Lubricant (gear oil)
- Race (bearing ring) or bearing surface
- Rolling elements (balls, rollers, needles)
- Cage (separator)
- Seals and glands
- Dirt and wear debris (dust, grit, water, metal particles)
- Contact mechanics (Hertzian contact)
- Magnetic bearing controller
- Rolling-contact fatigue
- Gear
represents (1)
Kinds (8)
- Machine elements
- Plain bearing
- Rolling-element bearing
- Jewel bearing
- Fluid bearing
- Magnetic bearing
- Flexure bearing
- Composite bearing
wired (3)
Notes published science
- About a fifth of all the energy the world uses goes to overcoming friction in rubbing and rolling contacts, and another 3% to rebuilding parts worn out by it (src:holmberg-2017-tribology-energy).
- Bacteria have a bearing: the flagellum's LP ring is a bushing round a rod that spins up to 1700 times a second, with only one or two layers of water molecules between rod and ring (src:yamaguchi-2021-flagellar-bushing).
- Ideas ran from machines to bodies: the first theories of how our knee and hip joints are lubricated were borrowed from bearing engineering, hydrodynamic wedges in 1932 and hydrostatic bearings in 1959 (src:mahadeshwara-2024-cartilage-lubrication).
Layers
The ways it takes in its world, where they meet, and how it acts back, each from L1 (where it meets the world) up.
the bearing as mechanical engineers describe it: load and motion in, constrained low-friction motion out (reader's view)
- L1: The world at the bearing: the load from shaft and housing (radial, axial, bending moment), the relative motion (speed as DN), the lubricant supplied, the heat of the surroundings, dirt and water, and stray electric currents
- L2: Its surfaces and doors: the inner and outer races (or the bore and journal of a plain bearing), fitted to shaft and housing by interference fit; the seals and glands; the grease fitting or oil cup
- L3: What lies between: balls or rollers held apart by a cage; or the lubricant film (hydrodynamic wedge, pumped hydrostatic film, thin EHD film); or the magnetic field; or the flexing element
- L4: The contact and its regime: Hertzian flattening of balls and races and the stresses under them; the lubrication regime (boundary, mixed, full film) set by viscosity, speed and load (the Stribeck curve); in the active magnetic kind, the controller
- L5: The loss ledger: friction torque and viscous dissipation turned to heat, carried off by the oil (the heat sink); wear; pumping or levitation power in fluid and magnetic kinds
- L6: Damage and life: fatigue spalls starting below the surface where shear peaks, abrasion, pressure welding, false brinelling, electrical fluting and white etching cracks; life as a statistic (L10, Weibull scatter, about five times L10 median)
- L7: The constrained motion delivered: only the desired motion freed (radial rotation, linear motion, spherical rotation, hinge motion), the others prevented, within the bearing's play and stiffness; the load passed to the supporting structure
the boardroom (shared floors)
- L4: The contact and its regime: Hertzian contact (ball and race flatten; stress peaks below the surface); the lubrication regime, boundary, mixed or full film, set by the Hersey number (viscosity times speed over load) on the Stribeck curve; rolling with little sliding
- L4: In the active magnetic kind: a controller (a microprocessor or digital signal processor) that offsets the bias currents of opposed electromagnet pairs to hold the rotor in the gap
- L5: The loss ledger: dissipated energy becomes heat at the surfaces; in real rolling bearings viscous dissipation in the EHL film dominates rolling resistance; the oil is the heat sink; hydrostatic pumps and active magnets draw power
- L6: Damage and life: rolling-contact fatigue (spalls from below the surface), abrasion and pressure welding, false brinelling, fluting and white etching cracks; life a statistical population (L10, Weibull slopes between 1 and 2)
- L7: The constrained motion delivered: only the desired motion, the load passed to the supporting structure, the shaft held within its play and stiffness
way in: Dirt and wear debris (dust, grit, water, metal particles)
- L1: Dust, grit and water from dirty surroundings (a rock crusher's conveyor), and the bearing's own wear debris
- L2: Seals and glands keep the dirt out (a door that refuses); Babbitt collects contaminants in its soft surface
- L3: Particles in the film: hard contaminants scrape the surfaces (abrasion) and dent them
way in: Heat (surroundings and the bearing's own friction)
- L1: Temperature of the surroundings and of the machine; heat made by friction at the surfaces in contact
- L2: Rings, housing and the oil take up the heat; oil flow cools the bearing metal by convection
- L3: Temperature sets the oil's viscosity, so the film; Martens plotted friction against temperature (that is, viscosity)
way in: Load (radial, axial and moment forces from shaft and housing)
- L1: Forces from the machine: predominately radial, axial (thrust) or bending moments perpendicular to the main axis; static, varying or shock loads
- L2: The races or bearing surface take it: each race has a groove the ball fits slightly loose in
- L3: Carried through the rolling elements (balls flatten slightly, races dent) or across the film
way in: Lubricant supply (oil, grease, solids, gases)
- L1: Lubricant brought by a ring oiler, splash, pressure oiling, a central lube system, a grease gun or an oil can; or the water a mill runs in
- L2: The doors: grease fitting, oil cup, oil passages, the gland that holds packed grease
- L3: The film between the surfaces: a thin elastohydrodynamic film in most rolling bearings and gears; a pumped or self-pressurised film in fluid bearings
way in: Relative motion (rotation or travel of the shaft)
- L1: The shaft's rotation (speed as DN, mean diameter times revolutions per minute) or a linear travel
- L2: The ring fitted to the shaft (interference fit, press or shrink fit) turns with it
- L3: The races' relative motion makes the rolling elements roll with little sliding; in a hydrodynamic bearing the journal drags fluid into the wedge
way in: Rotor position in the gap (active magnetic bearings only)
- L1: The rotor's place within the gap of the electromagnets
- L2: Gap sensors, usually inductive, sensing in a differential mode
- L3: Sensor electronics give the controller the feedback it needs
way in: Stray electric current (shaft voltage)
- L1: Shaft voltages from winding faults, unbalanced supplies, electrostatic effects and high-frequency PWM inverters
- L2: Rings and rolling elements act as the two sides of a gap with the lubricant film between: no prepared door
- L3: Discharges across the film, set by film thickness and contact area (so by temperature, load and speed)
way out: Guided motion and load into the frame
- L1: Axial and radial loads transferred to the structure supporting it
- L2: The outer ring in the housing bore (interference fit)
- L3: Through the rolling elements or the film to the other race
- L7: Only the desired motion let through; the shaft held on its axis
way out: Heat out
- L1: Carried away by the oil flow (convection) and the housing
- L2: Through rings and housing, and into the oil
- L5: Friction losses as heat
way out: Magnetic force on the rotor (active magnetic bearings)
- L1: Magnetic force on the rotor across the gap, with no contact
- L2: Solid-state power amplifiers (pulse-width modulation) drive the electromagnets
- L4: The controller's command
way out: Vibration and sound (the defect frequencies)
- L1: Vibration and sound, read by vibration, acoustic-emission and temperature sensors, and by people
- L2: Into the housing
- L3: Each rolling element striking the defect gives impacts at a frequency set by the geometry: BPFI, BPFO, BSF, FTF
- L6: A spall, dent or crack on a race, ball or cage
way out: Wear debris and spent lubricant out
- L1: Pushed out with older (grit-filled) grease by a fresh charge; excess oil back to the pool or sump
- L3: Debris carried in the film
- L6: Fatigue and welding tear out metal